Molex Micro-Fit 3.0 to J1708 6 Pin Gray Female and Male Connector Plug cable assembly
1.voltage :dc 300v 5m ohm/10 ms
2.contact resistance:3.0 ohm MAX
3.100% open ,Short ,Mis-Wirs Testing
SAE standards documents on OBD-II
- J1708 - Defines a standard used for serial communications between ECUs on a heavy duty vehicle and also between a computer and the vehicle.
- J1850 - Defines a serial data protocol. There are two variants- 10.4 kbit/s (single wire, VPW) and 41.6 kbit/s (two wire, PWM). Mainly used by US manufacturers, also known as PCI (Chrysler, 10.4 kbit/s), Class 2 (GM, 10.4 kbit/s), and SCP (Ford, 41.6 kbit/s)
- J1939 - Defines a data protocol for heavy duty commercial vehicles
- J1962 - Defines the physical connector used for the OBD-II interface.
- J1978 - Defines minimal operating standards for OBD-II scan tools
- J1979 - Defines standards for diagnostic test modes
- J2012 - Defines standards trouble codes and definitions.
- J2178-1 - Defines standards for network message header formats and physical address assignments
- J2178-2 - Gives data parameter definitions
- J2178-3 - Defines standards for network message frame IDs for single byte headers
- J2178-4 - Defines standards for network messages with three byte headers*
- J2284-3 - Defines 500 kbit/s CAN Physical and Data link layer
- J2411 - Describes the GMLAN (single-wire CAN) protocol, used in newer GM vehicles. Often accessible on the OBD connector as PIN 1 on newer GM vehicles.
DEUTSCH HD10 series connector
The HD series is an environmentally silicone rubber sealed, thermoplastic cylindrical connector, which is designed to be a faster, easier, trouble free assembly diagnostic connector in heavy-duty industry like truck, bus, cross-country vehicle,crane and forklift etc. When mated, the contacts are protected from water, dust, lubricating oils, fuel, road salt, grease, mud and other contaminants encountered.
- Operating at temperatures -40ºC to +125ºC, no Cracking, Chipping or leaking after 20 test cycles from -40ºC~+125ºC.
- No unlocking or unmating and exhibits no mechanical or physical damage after sinusoidal vibration levels of 20 G's at 10 to 2000Hz in each of the three mulually perpendicular planes for 2 hours. Force testing report as below shows
- IP68 rating, waterproof withstand immersion under 1.2 meter of water for 24 hours.
| Cavity |
Overall Length
A |
Overall Height
ØB |
Overall Length
C |
Overall Height
ØD |
| 3 |
1.609 (40.87) |
1.069 (27.15) |
1.639 (41.63) |
.851 (21.62) |
| 4 |
1.639 (41.63) |
1.595 (40.51) |
1.639 (41.63) |
1.281 (32.54) |
| 5 |
1.609 (40.87) |
1.218 (30.94) |
1.639 (41.63) |
1.001 (25.43) |
| 6 |
1.619 (41.12) |
1.453 (36.91) |
1.639 (41.63) |
1.141 (28.98) |
| 9 |
1.609 (40.87) |
1.593 (40.47) |
1.639 (41.63) |
1.281 (32.54) |
HD10 series
| Position |
Contact
Size |
Rear
Threads |
Plug |
Receptacle
Inline |
Receptacle
Flange |
3
|
16
|
no |
HD16-3-16S |
HD14-3-16P |
- |
| yes |
HD16-3-96S |
HD14-3-96P |
HD10-3-96P |
| 4 |
4/16 |
yes |
HD16-4-4S |
- |
HD10-4-4P |
| 5 |
16 |
no |
HD16-5-16S |
HD14-5-16P |
HD10-5-16P |
| 6 |
16 |
yes |
HD16-6-96S |
HD14-6-96P |
HD10-6-96P |
| 6 |
12 |
yes |
HD16-6-12S-B010 |
HD14-6-12P |
HD10-6-12P |
9
|
16
|
no |
HD16-9-16S |
HD14-9-16P |
HD10-9-16P |
| yes |
HD16-9-96S |
HD14-9-96P |
HD10-9-96P |
| 9 (J1939) |
16 |
yes |
HD16-9-1939S |
HD14-9-1939P |
HD10-9-1939P |
COMPANY PROFILE
☆ Privately held company, established in 1999
☆ Sales volume over 16 Million USD since 2017
☆ OEM & ODM company, with employees more than 250 persons, 7260 square-meters in size
☆ Service for economical solutions and innovative wire harnesses design & manufacturing
☆IATF16949 (2016) & ISO 9001 (2015), and UL certified supplier with wiring No. E468011 & cable No. E479323
CERTIFICATION
Q&A
1. Q: Can you help to design?
A: Yes, we are an ODM / OEM company, beyond we have been specializing in wire harness & Cable assembly since 1999.
2. Q: When will you start to help design?
A: We sketch simple solution for initial discussion, after quotation and order placed then start to drawing and double confirm with client for the design.
3. Q: What if quality issues occur when customer discover?
A: Our quality and engineer team will positively respond for the quality issues with 72 hours, as we are intend to make long-stand strategy with customer and the value is to provide better service.
4. Q: Do you have any standard products to cut down customers lead time for prototype and tooling cost?
A: Yes, there are over 1000 sets of molds and some of them can be used for customer directly. Moreover, Edgar is specialized in wire harness over 20
years with 5000+ products
CONTACT US
Audited Supplier 
){kind=link}