Micro-Fit 3.0 to 9 Pin HD Series J1939 HD10-9-1939p_B022 Automotive Diagnostic Wiring Harness

• Transport Package: Box
• Specification: 40*30*23
• Trademark: Edgarcn
• Origin: China
• Model NO.: HD series J1939 Black
• HS Code: 8544422900
• Production Capacity: 1000000 PCS Per Month

Product Description

Micro-Fit 3.0  to 9 Pin HD Series J1939 HD10-9-1939p_B022 automotive diagnostic wiring harness

1.voltage :dc 300v 5m ohm/10 ms
2.contact resistance:3.0 ohm MAX
3.100% open ,Short ,Mis-Wirs Testing

SAE standards documents on OBD-II

• J1708 - Defines a standard used for serial communications between ECUs on a heavy duty vehicle and also between a computer and the vehicle.
• J1850 - Defines a serial data protocol. There are two variants- 10.4 kbit/s (single wire, VPW) and 41.6 kbit/s (two wire, PWM). Mainly used by US manufacturers, also known as PCI (Chrysler, 10.4 kbit/s), Class 2 (GM, 10.4 kbit/s), and SCP (Ford, 41.6 kbit/s)
• J1939 - Defines a data protocol for heavy duty commercial vehicles
• J1962 - Defines the physical connector used for the OBD-II interface.
• J1978 - Defines minimal operating standards for OBD-II scan tools
• J1979 - Defines standards for diagnostic test modes
• J2012 - Defines standards trouble codes and definitions.
• J2178-1 - Defines standards for network message header formats and physical address assignments
• J2178-2 - Gives data parameter definitions
• J2178-3 - Defines standards for network message frame IDs for single byte headers
• J2178-4 - Defines standards for network messages with three byte headers*
• J2284-3 - Defines 500 kbit/s CAN Physical and Data link layer
• J2411 - Describes the GMLAN (single-wire CAN) protocol, used in newer GM vehicles. Often accessible on the OBD connector as PIN 1 on newer GM vehicles.

DEUTSCH HD10 series connector 

The HD series is an environmentally silicone rubber sealed, thermoplastic cylindrical connector, which is designed to be a faster, easier, trouble free assembly diagnostic connector in heavy-duty industry like truck, bus, cross-country vehicle,crane and forklift etc. When mated, the contacts are protected from water, dust, lubricating oils, fuel, road salt, grease, mud and other contaminants encountered.

• Operating at temperatures -40ºC to +125ºC, no Cracking, Chipping or leaking after 20 test cycles from -40ºC~+125ºC.

• No unlocking or unmating and exhibits no mechanical or physical damage after sinusoidal vibration levels of 20 G's at 10 to 2000Hz in each of the three mulually perpendicular planes for 2 hours. Force testing report as below shows

• IP68 rating, waterproof withstand immersion under 1.2 meter of water for 24 hours.

 

Cavity	Overall Length A	Overall Height ØB	Overall Length C	Overall Height ØD
3	1.609 (40.87)	1.069 (27.15)	1.639 (41.63)	.851 (21.62)
4	1.639 (41.63)	1.595 (40.51)	1.639 (41.63)	1.281 (32.54)
5	1.609 (40.87)	1.218 (30.94)	1.639 (41.63)	1.001 (25.43)
6	1.619 (41.12)	1.453 (36.91)	1.639 (41.63)	1.141 (28.98)
9	1.609 (40.87)	1.593 (40.47)	1.639 (41.63)	1.281 (32.54)

HD10 series
 

Position	Contact Size	Rear Threads	Plug	Receptacle Inline	Receptacle Flange
3	16	no	HD16-3-16S	HD14-3-16P	-
		yes	HD16-3-96S	HD14-3-96P	HD10-3-96P
4	4/16	yes	HD16-4-4S	-	HD10-4-4P
5	16	no	HD16-5-16S	HD14-5-16P	HD10-5-16P
6	16	yes	HD16-6-96S	HD14-6-96P	HD10-6-96P
6	12	yes	HD16-6-12S-B010	HD14-6-12P	HD10-6-12P
9	16	no	HD16-9-16S	HD14-9-16P	HD10-9-16P
		yes	HD16-9-96S	HD14-9-96P	HD10-9-96P
9 (J1939)	16	yes	HD16-9-1939S	HD14-9-1939P	HD10-9-1939P

COMPANY PROFILE
 

☆ Privately held company, established in 1999
☆ Sales volume over 16 Million USD since 2017 
☆ OEM & ODM company, with employees more than 250 persons, 7260 square-meters in size 
☆ Service for economical solutions and innovative wire harnesses design & manufacturing 
☆IATF16949 (2016) & ISO 9001 (2015), and UL certified supplier with wiring No. E468011 & cable No. E479323







CERTIFICATION



Q&A   

1. Q: Can you help to design?
A: Yes, we are an ODM / OEM company, beyond we have been specializing in wire harness & Cable assembly since 1999.
2. Q: When will you start to help design?
A: We sketch simple solution for initial discussion, after quotation and order placed then start to drawing and double confirm with client for the design. 
3. Q: What if quality issues occur when customer discover?
A: Our quality and engineer team will positively respond for the quality issues with 72 hours, as we are intend to make long-stand strategy with customer and the value is to provide better service.
4. Q: Do you have any standard products to cut down customers lead time for prototype and tooling cost?
A: Yes, there are over 1000 sets of molds and some of them can be used for customer directly. Moreover, Edgar is specialized in wire harness over 20
years with  5000+  products

CONTACT US