| Type: | Insulated |
|---|---|
| Conductor Type: | Stranded |
| Application: | Overhead |
| Conductor Material: | Copper |
| Sheath Material: | PVC |
| Insulation Material: | XLPE |
| Customization: |
|---|
Suppliers with verified business licenses
Audited Supplier OBD II J1962 16 PIN Male to OBD-II Flange Type for Chavrolet Cable
1.voltage :dc 300v 5m ohm/10 ms
2.contact resistance:3.0 ohm MAX
3.100% open ,Short ,Mis-Wirs Testing
SAE standards documents on OBD-II
The SAE J1962 specification provides for two standardized hardware interfaces, called type A and type B. Both are female, 16-pin (2x8), D-shaped connectors, and both have a groove between the two rows of pins, but type B's groove is interrupted in the middle. This prevents the insertion of a type A male plug into a type B female socket while allowing a type B male plug to be inserted into a type A female socket.
The type A connector is used for vehicles that use 12V supply voltage, whereas type B is used for 24V vehicles and it is required to mark the front of the D-shaped area in blue color.
| Pin Number | Description |
|---|---|
| 1 | Manufacturer Discretionary |
| 2 | SAE J1850 Bus + (VPW / PWM) |
| 3 | Manufacturer Discretionary |
| 4 | Chassis Ground |
| 5 | Signal Ground |
| 6 | CAN High (ISO 15765-4 and SAE J2284) |
| 7 | ISO 9141-2 / ISO 14230-4 K Line |
| 8 | Manufacturer Discretionary |
| 9 | Manufacturer Discretionary |
| 10 | SAE J1850 Bus - (PWM-only) |
| 11 | Manufacturer Discretionary |
| 12 | Manufacturer Discretionary |
| 13 | Manufacturer Discretionary |
| 14 | CAN Low (ISO 15765-4 and SAE J2284) |
| 15 | ISO 9141-2 / ISO 14230-4 L Line (Optional) |
| 16 | Vehicle Battery Power:
|
Material: PA66, tined plated compliant ROHS,
Working temperature: -20~80°C
Over-molding: customized
Pitch: 4mm
Voltage: 12V for car and 24V for heavy vehicle
DEUTSCH HD10 series connector
The HD series is an environmentally silicone rubber sealed, thermoplastic cylindrical connector, which is designed to be a faster, easier, trouble free assembly diagnostic connector in heavy-duty industry like truck, bus, cross-country vehicle,crane and forklift etc. When mated, the contacts are protected from water, dust, lubricating oils, fuel, road salt, grease, mud and other contaminants encountered.
Operating at temperatures -40ºC to +125ºC, no Cracking, Chipping or leaking after 20 test cycles from -40ºC~+125ºC.
No unlocking or unmating and exhibits no mechanical or physical damage after sinusoidal vibration levels of 20 G's at 10 to 2000Hz in each of the three mulually perpendicular planes for 2 hours. Force testing report as below shows
IP68 rating, waterproof withstand immersion under 1.2 meter of water for 24 hours.
| Cavity | Overall Length A |
Overall Height ØB |
Overall Length C |
Overall Height ØD |
| 3 | 1.609 (40.87) | 1.069 (27.15) | 1.639 (41.63) | .851 (21.62) |
| 4 | 1.639 (41.63) | 1.595 (40.51) | 1.639 (41.63) | 1.281 (32.54) |
| 5 | 1.609 (40.87) | 1.218 (30.94) | 1.639 (41.63) | 1.001 (25.43) |
| 6 | 1.619 (41.12) | 1.453 (36.91) | 1.639 (41.63) | 1.141 (28.98) |
| 9 | 1.609 (40.87) | 1.593 (40.47) | 1.639 (41.63) | 1.281 (32.54) |
| Position | Contact Size |
Rear Threads |
Plug | Receptacle Inline |
Receptacle Flange |
| 3 |
16 |
no | HD16-3-16S | HD14-3-16P | - |
| yes | HD16-3-96S | HD14-3-96P | HD10-3-96P | ||
| 4 | 4/16 | yes | HD16-4-4S | - | HD10-4-4P |
| 5 | 16 | no | HD16-5-16S | HD14-5-16P | HD10-5-16P |
| 6 | 16 | yes | HD16-6-96S | HD14-6-96P | HD10-6-96P |
| 6 | 12 | yes | HD16-6-12S-B010 | HD14-6-12P | HD10-6-12P |
| 9 |
16 |
no | HD16-9-16S | HD14-9-16P | HD10-9-16P |
| yes | HD16-9-96S | HD14-9-96P | HD10-9-96P | ||
| 9 (J1939) | 16 | yes | HD16-9-1939S | HD14-9-1939P | HD10-9-1939P |
COMPANY PROFILE
☆ Privately held company, established in 1999
☆ Sales volume over 16 Million USD since 2017
☆ OEM & ODM company, with employees more than 250 persons, 7260 square-meters in size
☆ Service for economical solutions and innovative wire harnesses design & manufacturing
☆IATF16949 (2016) & ISO 9001 (2015), and UL certified supplier with wiring No. E468011 & cable No. E479323
CERTIFICATION
Q&A
1. Q: Can you help to design?
A: Yes, we are an ODM / OEM company, beyond we have been specializing in wire harness & Cable assembly since 1999.
2. Q: When will you start to help design?
A: We sketch simple solution for initial discussion, after quotation and order placed then start to drawing and double confirm with client for the design.
3. Q: What if quality issues occur when customer discover?
A: Our quality and engineer team will positively respond for the quality issues with 72 hours, as we are intend to make long-stand strategy with customer and the value is to provide better service.
4. Q: Do you have any standard products to cut down customers lead time for prototype and tooling cost?
A: Yes, there are over 1000 sets of molds and some of them can be used for customer directly. Moreover, Edgar is specialized in wire harness over 20
years with 5000+ products
CONTACT US
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}